A2 2000 petrol NO(1) SPECIFIC VEHICLE ALARM FITTING INSTRUCTIONS REV...
Serwis znalezionych hasełOdnośniki
- Smutek to uczucie, jak gdyby się tonęło, jak gdyby grzebano cię w ziemi.
- pozytywistycznych, które wszelkie warianty artyzmu traktują jako instrumenty krasomówcze, a wartość słowa poetyckiego pragną mierzyć wartością...
- do apteki, wykupuje receptę i postępuje zgodnie z instrukcjami lekarza, na przykład: “zażywać dwie tabletki co cztery godziny"...
- J29typ ruchowy, b'd¹cy podstaw¹ efektywnego wykonania okreœlonej ewolucji podc2 gry na instrumencie...
- Zdjęcia pokazywały niemieckich inżynierów-elektroników instruujących lokalny nowojorski personel...
- zagranicznych partnerów – to naleŜy dostępnymi instrumentami polityki gospodarczejtaki popyt stymulować...
- Faulk poczuł dłoń drugiego instruktora na swoim ramieniu...
- After you build the system and get it running, it’s important to do a reality check, and here’s where the requirements analysis and system specification comes in...
- LCC–00114 illegal boolean response character Cause A value other than TRUE or FALSE was specified...
- What a particular country’s GDP per capita will be in the future, depends on its value at the point of departure in 2000 and the pace of growth over the next decades...
- wkładki z bombonierki...
Smutek to uczucie, jak gdyby się tonęło, jak gdyby grzebano cię w ziemi.
00
www.cobra.it
X
MAKE
AUDI
MOD.
A2
YEAR.
00 → PETROL
DIESEL
ALARM/SIREN
Position the compact alarms and the sirens on the support of the shock absorber POSITION
passenger’s side. Pass the cables through the original rubber core hitch located on the panel that divides the engine compartment and the passenger’s compartment, passenger’s side.
CENTRAL UNIT POSITION
Position the modular systems and the modules under the dashboard, driver’s side.
POWER SUPPLY
+ 30: connect to the 4 mm2 RED wire located in a multiway connector at the entrance of the fuse box.
- 31: connect with a ring terminal directly to the car body.
IGNITION WIRE
+ 15/54: connect to the RED/GREEN wire at the position nr. 17 located in the 17
way black connector, on the connectors holder plate under the moquette on front of the driver’s seat.
DIRECTION INDICATORS
Connect to the BLACK/WHITE and BLACK/GREEN wires in the wiring harness behind the sill cover driver’s side.
ELECTRIC WINDOWS
Negative control signal The closing of the electric windows is obtained timing to 24s the same GREY/GREEN wire used for the closing of the doors.
CENTRAL DOORS LOCKING
Negative control signal Connect to the GREY/GREEN wire (lock) and GREY/VIOLET wire (unlock) located in the wiring harness directly coming out from the lock inside the driver’s side door.
IMMOBILISATION POINT
Fuel pump
Cut the BLACK/BLUE wire located at the position nr. 4, in the 10 way grey connector, behind the driver’s side bulkhead.
STARTER
+50: Cut the RED/GREEN wire located in the wiring harness coming out of the ignition key.
BONNET SWITCH
Install an additional switch on the front headlamp support plate, driver’s side.
DOORS SWITCH
Connect to the BROWN/WHITE wire at the position nr. 2 in the 12 way black connector coming out of the modular system located under the moquette on front of the drivers seat.
BOOT SWITCH
Connect to the BROWN/PINK wire at the position nr. 11 located in the 16 way LIGHT BROWN connector coming out of the modular system under the moquette on front of the driver’s seat.
Note: This information is not binding, therefore it must be considered only an example for installation purposes that must be executed aua200gbb.doc
as per the instructions given on the product installation manual.